天津11选5走势图

山东优泉保温建材有限公司
地址:齐河县焦庙镇小李村西邻
联系人:卢经理
电话:0531-87266820
传真:0531-87266820
邮箱:390062028@qq.com
网址:
当前位置:首页 - 技术与应用
技术与应用
挤塑板XPS薄抹灰保温系统的滴水线制作
作者:admin 来源:本站 发布时间:2018-10-25 15:23:01 浏览次数:425
1.外墙xps保温板某一面因包装、运输等原因造成微小的缺陷时,则应将这一面作为抹胶面。
1. When one side of the exterior wall XPS insulation board is slightly defective due to packaging, transportation and other reasons, this side should be used as a plastering surface.
2.将涂抹好胶粘剂的xps保温板紧密地粘贴在墙面上(或插入托架),在粘贴下一块xps保温板时,应将这块板从侧面推压向前一块板,并保证xps保温板与xps保温板之间的接缝被压紧。在墙角托架处,玻璃纤维网格布应延伸至托架的底边边缘,多余部分用刀切除。
2. The XPS insulation board coated with adhesive is tightly pasted on the wall (or inserted into the bracket). When pasting the next XPS insulation board, the board should be pushed forward from the side and the joint between the XPS insulation board and the XPS insulation board should be tightened. At the corner bracket, the fiberglass mesh should be extended to the bottom edge of the bracket, and the excess parts should be cut off with a knife.

3.粘贴xps保温板缝应轻揉,均匀挤压、挤紧,xps保温板缝应错开,相邻外墙xps保温板应齐平,粘结砂浆挤出时用铲刀立即刮掉,使xps保温板与xps保温板之间无"碰头灰"。xps保温板间缝隙不得大于2㎜,xps保温板缝隙大于2㎜时,应用xps保温板条将缝塞满,xps保温板条不得粘结,更不得用胶粘剂直接填缝。

山东挤塑板

3. Paste the seam of the XPS insulation board should be rubbed lightly, evenly extruded and squeezed, the seam of the XPS insulation board should be staggered, the adjacent exterior wall XPS insulation board should be even, the bonded mortar should be scraped off imtely with a spade when extruding, so that there is no "contact ash" between the XPS insulation board and the XPS insulation board. When the gap between the XPS insulation board is larger than 2 and the gap between the XPS insulation board is larger than 2, the crack can be filled with the XPS insulation board, and the XPS insulation board can not be bonded, and the adhesive can not be used to fill the seam directly.
4.xps保温板间高差不得大于1.5㎜(或4㎜/2m),当xps保温板间高差有大于1.5㎜的部位,应在粘胶硬化后做轻柔圆周运动打磨平整。
4. The height difference between XPS insulating boards should not be greater than 1.5(or 4/2m). When the height difference between XPS insulating boards is greater than 1.5(or 4/2m), it should be smoothed by gentle circular motion after the viscose hardening.
5.在门窗四角与墙面平行方向粘贴xps保温板时,需注意在开角处不得有板缝,应以整块xps保温板在该处粘贴,粘贴前先在xps保温板上裁切处门窗开角。
5. When pasting the XPS insulation board in the four corners of doors and windows parallel to the wall surface, it should be noted that there is no board seam at the opening angle. The whole XPS insulation board should be pasted here. The opening angle of the door and window should be cut on the XPS insulation board before pasting.
6.在门窗沿作xps保温板处理时,与墙面平行的xps保温板粘贴应超出原门窗沿距离,即门窗沿处xps保温板及其胶粘剂厚度之和。
6. When the windows and doors are treated with the XPS insulation board, the distance of the XPS insulation board parallel to the wall should exceed the distance of the original windows and doors, that is, the thickness of the XPS insulation board and its adhesive along the windows and doors.
7.门窗洞口四角(突出管线、埋件)的xps保温板应采用整块板割成形(套割吻合),不得拼接。外保温体系与其建筑构件或材料(如门窗框、窗台板、阳台、楼顶板等)的接缝处用膨胀密封条做防水处理。
7. The XPS insulating sheet at the four corners of the entrance of doors and windows (protruding pipelines and buried parts) should be cut into whole sheets (sleeve cutting anastomosis), and should not be spliced. External insulation system and its building components or materials (such as doors and windows frames, windowsill panels, balconies, roof panels, etc.) joints with expansion sealing strip waterproof treatment.
更多的关于济南挤塑板厂家问题或者详细的内容,请进入我们公司的网站:网站中会有很多的内容仅供参考。
For more inion about Jinan Extrusion board manufacturers, please visit our company's website: , there will be a lot of content for reference only.
友情链接:大无限彩票  传奇彩票  幸运彩票  博九彩票网  博九彩票网  博九彩票官网  

免责声明: 本站资料及图片来源互联网文章,本网不承担任何由内容信息所引起的争议和法律责任。所有作品版权归原创作者所有,与本站立场无关,如用户分享不慎侵犯了您的权益,请联系我们告知,我们将做删除处理!