幸运飞艇

山东优泉保温建材有限公司
地址:齐河县焦庙镇小李村西邻
联系人:卢经理
电话:0531-87266820
传真:0531-87266820
邮箱:390062028@qq.com
网址:
当前位置:首页 - 技术与应用
技术与应用
聚苯板粘贴质量在于细节
作者:admin 来源:本站 发布时间:2017-05-06 11:28:15 浏览次数:247
  1、聚苯板粘贴配置粘结砂浆:根据产品说明配置粘结砂浆,拦好的浆料在静置10分钟后,还需再次搅拌才能使用。配好的料注意防晒避风,一次配置量应在2小时内用完。
Binding mortar: 1, polystyrene paste configuration according to the instructions to configure binding mortar, block good pulp after let stand for 10 minutes, still need to stir again to use. Be sure to pay attention to the sun protection, the amount should be used within 2 hours. 
2、施工前,根据整个外墙立面的设计尺寸编制聚苯板的排板图,聚苯板以长向水平铺贴,保证连续结合,上下两排板竖向错缝不得小于200mm。
2, before the construction, according to the exterior facade of the size of polystyrene plate number, compiling of polystyrene to level the shop is stuck with a long, continuous, up and down two rows of plate vertical staggered joints shall not be less than 200 mm. 
3、按尺寸切割聚苯板,从拐角处垂直错缝连结,要求拐角处沿建筑物全高顺直、完整。

To cut the polyphenylene plate according to the size of the corner, and to make the whole point along the corner of the building. 

山东挤塑板价格

4、粘贴方式有点框法和条粘法。占框法适用于平整度较差的墙面,粘结面积不小于40%。具体粘结方法为;在每块聚苯板周边涂50mm宽的粘结砂浆,要求从边缘向中间逐渐加厚,最厚处达10mm。
The method of pasting is a bit of box and stick. The frame method is applied to the wall with poor adjustment, and the bond area is not less than 40%. The concrete bond method is; The thickness of the mortar, which is 50mm wide, is required to be thickened from the edge to 10mm thick. 
5、聚苯板的粘贴应从细部节点及阴阳角部位向中间进行。板缝应挤压,相领板应奇平,施工时控制板间缝隙不得大于2mm,板条不得用砂浆或胶结剂粘结;板间平整度高差大于1.5mm的部位应在施工面层前用木锉、粗砂纸或砂轮打磨平整。
The pasting of the polyphenylene plate should be carried out from the detail and the Angle of Yin and Yang. The seam should be squeezed and the collar plate should be square, and the gap between the control panel should not be greater than 2mm in the construction time, the slurry should not be bonded with mortar or cement. The area of horizontal adjustment of plate is bigger than 1.5 mm area should be in the construction face layer before use wood file, coarse sandpaper or grinding wheel is ground and level. 
6、在门窗洞口部位的聚苯板不允许用碎板拼凑,需用整幅板裁切出门窗四角及洞口形状,其它接缝距洞口四边应大于200mm。
6, in the Windows and doors mouth parts of polystyrene are not allowed to use broken board together, need the whole picture of plate cutting corners of doors and Windows and the entrance of the cave shape, other joint from the mouth of the cave edges should be greater than 200 mm. 
感谢大家在百忙之中关注公司发布的产品信息,如果你想要了解更多,可以来我们公司咨询。我们欢迎大家的光临,并与你的合作!
Thank you for your attention to the product inion released by the company. If you want to know more, we can consult our company. We welcome your presence and cooperate with you! 

友情链接:幸运彩票官网  传奇彩票官网  传奇彩票  幸运彩票  幸运彩票  博九彩票  

免责声明: 本站资料及图片来源互联网文章,本网不承担任何由内容信息所引起的争议和法律责任。所有作品版权归原创作者所有,与本站立场无关,如用户分享不慎侵犯了您的权益,请联系我们告知,我们将做删除处理!