天津11选5走势图

山东优泉保温建材有限公司
地址:齐河县焦庙镇小李村西邻
联系人:卢经理
电话:0531-87266820
传真:0531-87266820
邮箱:390062028@qq.com
网址:
当前位置:首页 - 技术与应用-技术支持
技术与应用
挤塑板界面剂的处理工艺介绍
作者:admin 来源:本站 发布时间:2016-04-28 13:48:55 浏览次数:455
施工时,用腻子刮板将配置好的胶料刮抹于挤塑板表面,厚度为1mm,用力要均匀,使胶料均匀分布在挤塑板的表面。山东挤塑板
Construction, use putty scraper will configure the rubber materials wiped on the surface of the extruded plate thickness of 1 mm, force should be uniform, the glue material is evenly distributed on the surface of plastic extruded board.
挤塑板间的缝隙宜小于等于3㎜,嵌入缝隙内的水泥浆清除深度大于等于10㎜,挤塑板间的缝隙用NP中性硅酮密封胶或JS挤塑板界面剂嵌填饱满。外墙面局部损伤的挤塑板,应将其轮廓裁切成矩形,用周圈抹JS界面剂相应形状的挤塑板嵌填补齐。

Extruded plate gap should be less than or equal to 3 mm, embedded in the crevice of cement slurry removal depth greater than or equal to 10 mm, extruded board slot with NP neutral silicone sealant or JS extruded board, interface agent block filled full. Outside the walls of local damage of plastic extruded board, will the contour cut into rectangles, wipe JS interface agent corresponding to the shape of the extruded plate embedded fill filled with a circle.

山东挤塑板

辅助模板拆除后,对外漏的挤塑板应及时刮抹界面剂。遭水泥砂浆污染的挤塑板表面,在刮抹JS挤塑板界面剂前应用粗砂纸打磨清洁。季节性施工时,山东挤塑板可以起到外墙模板蓄热保温材料的作用,但当环境温度低于5℃时,挤塑板表面应刮抹防冻型JS-2挤塑板界面剂,技术指标应达到-15℃。
After removing the template assisted, extruded plate leakage should be timely scraping the external interface agent. Extruded plate surface by cement mortar in pollution, scraping the JS board interface agent before the application of coarse sandpaper clean. Seasonal construction, Shandong plastic extruded board can play to the external walls of the template heat preservation material, but when the environment temperature is lower than 5 DEG C, plastic extruded board surface should wiped antifreeze JS-2 plastic extruded board interface agent, technical indicators should reach 15 DEG C.
雨期施工时,应在挤塑板表面刮抹JS-1挤塑板界面剂,刮抹应在无明水 的状态下进行。若处在烈日暴晒下,挤塑板表面宜用湿布擦拭,轻微润湿阴干。刮抹 界面剂,宜适当遮阳,刮抹完毕后,待表面初步结硬,宜用喷雾器喷水养护4h。
During the construction, should be in the extrusion plate surface scraping JS-1 board interface agent, scraping should be carried out in the state of no water. If in the hot sun, extruded plate surface should use a damp cloth, slightly wetting drying. Scraping and wiping the interface agent should be appropriate to the sun, scraping, after the completion of the initial surface to be hard, appropriate to use spray water conservation 4h.
挤塑板开孔外墙外侧模板就位后,根据外模穿墙螺栓的位置,用挤塑板开孔器将挤塑板开洞,挤塑板开孔器应旋转推进,保证开洞的尺寸规矩,并不损伤挤塑板。开洞后安穿墙拉杆及套管。内模就位将外墙内侧模板按预定位置就位,用常规方法合模即可。挤塑保温板竖排至门、窗口时,可根据需要横绑在外墙面上,使其不出现细窄拼条。
After opening hole outside the external wall template in place of plastic extruded board, according to the position of the outer mold wall bolt, plastic extruded board open hole is extruded plate opening, extruded plate with a hole for rotating push to ensure opening size rule, does not damage the plastic extruded board. Safety rod and casing wall with openings. Internal mold in place will be in place of the outer wall of the template at a predetermined position, with the conventional method can be combined. Vertical to Extrusion insulation board door and window, can be cross tied on the external wall, it does not appear narrow together.
友情链接:博九娱乐网  博九娱乐网  传奇彩票官网  传奇彩票  传奇彩票  幸运彩票官网  

免责声明: 本站资料及图片来源互联网文章,本网不承担任何由内容信息所引起的争议和法律责任。所有作品版权归原创作者所有,与本站立场无关,如用户分享不慎侵犯了您的权益,请联系我们告知,我们将做删除处理!