天津11选5走势图

山东优泉保温建材有限公司
地址:齐河县焦庙镇小李村西邻
联系人:卢经理
电话:0531-87266820
传真:0531-87266820
邮箱:390062028@qq.com
网址:
当前位置:首页 - 新闻动态
新闻动态
挤塑板的粘结工艺是怎么样的?
作者:admin 来源:本站 发布时间:2019-06-25 10:50:39 浏览次数:124
  在外墙保温施工中,挤塑板的粘结过程是什么,保温告诉你答案。
In the construction of exterior wall insulation, what is the bonding process of extrusion board? The insulation tells you the answer.
1. 如果保温板是挤塑板,则应在粘接剂的一侧涂上特殊的界面剂,静置20分钟晾干。
1. If the insulation board is an extruded board, special interfacial agent should be applied on the side of the adhesive and let it stand for 20 minutes to dry.
2. 挤塑板一般由下向上水平铺设,错缝宽度为板长1/2。必要时进行适当切割,尺寸偏差不大于±1.5mm。
2. Extruded sheets are generally laid horizontally from the bottom to the top, and the width of staggered joints is 1/2 of the length of the sheet. If necessary, cut properly, and the size deviation is not more than (+1.5mm).
3.将挤塑板周围均匀的一层粘合剂聚合物砂浆涂抹宽度是50毫米,厚度是10毫米,板的一侧,并留出50毫米宽口,中间部分采用一些粘粘的,直径100毫米,10毫米的厚度,中心距200毫米,为1200 mm x 600 mm标准板,中间有八个点,为非标准板,应挤塑板粘贴后,涂抹的粘液面积不少于30%的面积。木板的一面不能粘。

3. The uniform layer of adhesive polymer mortar around the Extrusion board is coated with a width of 50 mm, a thickness of 10 mm, one side of the board, and a width of 50 mm. The middle part is made of some sticky, 100 mm in diameter, 10 mm in thickness, 200 mm in center distance, 1200 mm x 600 mm standard board. There are eight points in the middle, which are non-standard plates. After the Extrusion board is pasted, the area of the adhesive applied is not less than 30%. The measure of area. One side of the board can't stick.

4. 如果基础墙平整度较好,也可以采用条带粘贴的方法,宽度为10mm,厚度为10mm,间距为50mm。
4. If the flatness of the foundation wall is good, the method of strip bonding can also be used. The width is 10 mm, the thickness is 10 mm, and the spacing is 50 mm.
5. 将保温板立即粘贴在墙面上,滑动到位,用尺用2米将其压平,确保其平整度并粘贴牢固。
5. Insulate the insulation board on the wall imtely, slide it in place, and press it down with a ruler of 2 meters to ensure its smoothness and firm adhesion.
6. 当板材间隙大于2mm时,板材之间的高差不得大于1.5mm。当板与板之间的间隙大于2mm时,绝缘条应使用填充接缝。带材不能粘接,也不能用粘接剂直接填满接头。
6. When the clearance between sheets is greater than 2 mm, the height difference between sheets should not be greater than 1.5 mm. When the gap between the board and the board is larger than 2 mm, the filling joint should be used for the insulating strip. Strip can not be bonded, nor can it be directly filled with adhesives.
7. 所有门窗、墙角处的孔不得拼接接缝,保温板必须用于切割成型,且墙角处的板缝不得小于200mm
7. All holes in doors, windows and corners shall not be spliced. Insulation boards shall be used for cutting and shaping, and the cracks in corners shall not be less than 200 mm.
8. 在所有阴、阳角处,必须采用错缝粘贴法,并按垂直线用尺控制偏差,用90°尺检查。
8. In all Yin and Yang angles, staggered seam sticking method must be used, and the deviation should be controlled by ruler according to vertical line, and checked by 90 degree ruler.
友情链接:博九彩票注册  幸运彩票官网  博九娱乐网  博九彩票  幸运彩票官网  博九彩票  

免责声明: 本站资料及图片来源互联网文章,本网不承担任何由内容信息所引起的争议和法律责任。所有作品版权归原创作者所有,与本站立场无关,如用户分享不慎侵犯了您的权益,请联系我们告知,我们将做删除处理!