幸运飞艇

山东优泉保温建材有限公司
地址:齐河县焦庙镇小李村西邻
联系人:卢经理
电话:0531-87266820
传真:0531-87266820
邮箱:390062028@qq.com
网址:
当前位置:首页 - 新闻动态
新闻动态
XPS挤塑板质量标准!
作者:admin 来源:本站 发布时间:2019-03-07 14:53:59 浏览次数:68
  XPS挤塑板质量标准主要体现在两个方面,一个是主控项目,一个是在一般项目的标准。下面,挤塑板生产厂家来和我们详细介绍一下。
XPS Extrusion board quality standards are mainly reflected in two aspects, one is the main control project, the other is the general project standards. Next, the Extrusion board manufacturers come and give us a detailed introduction.
1、主控项目
1. Main control project
(1)网格布的规格和各项技术指标,粘结剂、聚合物砂浆的配置及其原料的质量,必须符合有关标准和正常使用要求。
(1) The specifications and technical specifications of mesh cloth, the configuration of binder and polymer mortar and the quality of raw materials must conform to relevant standards and normal use requirements.
(2)XPS挤塑板必须与墙面粘结牢固,无松动和虚粘现象。
(2) XPS Extrusion board must be firmly bonded to the wall without loosening or virtual sticking.
(3)聚合物水泥砂浆与挤塑板必须粘结牢固,无脱层、空鼓,面层无爆灰和裂缝。
(3) Polymer cement mortar and Extrusion board must be firmly bonded, without delamination, hollow drum, explosive ash and cracks on the surface.
2、一般项目
2. General items
(1)每块挤塑板与墙面的总粘结面积,首层不得小于60%,其他层不得小于30%。
(1) The total bonding area between each extruded panel and the wall shall not be less than 60% on the first floor and 30% on the other.
(2)聚乙烯胀塞全部进入结构墙体。
(2) All polyethylene expansion plugs enter the structural wall.
(3)挤塑板碰头不抹粘结剂。

(3) No binder is applied to the contact of the extruded board.

(4)挤塑板贴完后,需用2m靠尺及楔形塞尺检查板面平整度和垂直度,误差均不大于2mm(2m之内),阴阳角处板边加工与连接也必须整齐平顺。
(4) After pasting the extruded board, the flatness and verticality of the board surface should be checked by 2m ruler and wedge plug ruler. The error is no more than 2mm (within 2m). The edge processing and connection of the board at the Yin and Yang angles must also be neat and smooth.
(5)墙面装饰用凹凸线条必须水平或竖直,凹线条及贴上的凸线条须用2m靠尺及楔形塞尺检查平整度,误差不大于2mm。
(5) The concave and convex lines for wall decoration must be horizontal or vertical. The concave and affixed convex lines must be checked by 2m ruler and wedge-shaped plug ruler. The error is not more than 2mm.
(6)用插针方法检查抹面胶浆的厚度。网格布置应横向铺设,压贴密实,不能有空鼓、褶皱、翘曲、外露等现象,搭接宽度左右不得小于150mm,上下不得小于100mm。
(6) Inserting needle method was used to check the thickness of the paste. The grid layout should be laid horizontally and compactly. There should be no empty drum, fold, warpage and exposure. The lap width should not be less than 150 mm, and the top and bottom should not be less than 100 mm.
(7)聚合物水泥砂浆保护层总厚度不宜大于7mm,首层不宜大于9mm。
(7) The total thickness of protective layer of polymer cement mortar should not be greater than 7 mm, and the first layer should not be greater than 9 mm.
友情链接:传奇彩票  传奇彩票  博九彩票  幸运彩票  博九彩票  传奇彩票  

免责声明: 本站资料及图片来源互联网文章,本网不承担任何由内容信息所引起的争议和法律责任。所有作品版权归原创作者所有,与本站立场无关,如用户分享不慎侵犯了您的权益,请联系我们告知,我们将做删除处理!